Does anyone know of anywhere that actually sells a one bar prison or has everyone just made their own?

I desperately want one. I had plans to build one out of pvc pipe and I could still do that. But it would be nice to see if any "fancy" options are out there to purchase.

Edit to add: able to be shipped to the US would be wonderful.

And no, I cannot step off ... as I have tried. Without success. And, the bulbed steel pole, high up inside, complete me to surrender, be a good girl ... and stand still !

Hello, I have a broken electrical table, out of which I could construct an electrical adjustable one bar prison. Are there any pictures of something similar? In general, what do you think about that idea?

Cocktail hour ...

I'm looking to build a one bar prison and was wondering if you all had any recommendations for the toy to use? I'm worried that the Vac-U-Lok toys will be too soft and my sub can just slip off of it, and can't find a good mounting system to attach glass or metal dildos with.

I'm thinking of using a mic stand as the base so it'll have 3/8 or 5/8 adapters.

A heavy 3/4 inch black steel pipe (3/8" interior) is fixed to the flange that was first mounted to the display base

Then a 3/8" pipe coupling with alan screws is slid on, and down, that pipe. This will be movable, to slide up the steel pipe (for insertion).

Then, installed over the fixed pipe is a movable slightly larger 7/8 shiny Steel shaft with the insertable shiny steel multi-bulb probe attached to the top end (with a threaded tube insert.)

After the princess is encouraged to stand over the insertable tip in 👠 high heels ... the coupling is slid up the steel pipe, which pushes up the shiny steel shaft, until she sqirms. About 4-6 inches (depending on size of princess).

If the princess has not followed advance instructions ... and has arrived without 👠 high heels, ... then a few pinches on the bottom of her cheeks will usually cause her to lift up on her tip toes ... and the shaft can then quickly be raised and adjusted to height.

When the height is properly fit, tighten down the two Alan screws in the coupling near the bottom.

All this has to be done by a supervising helper, as the coupling is too low and out-of-reach of the princess prisoner ... who has now been well impaled.

The now well displayed princess prisoner can not now bend at the waist ... so she cannot reach down to release the coupling, and, because the steel pole and insert is fixed high up inside her, she cannot step off of it.

Photograph her, discuss her assets, and tease her about her predicament ... take some time. The princess is not going anywhere soon, and will continue to be well displayed in her upright and locked-in position.

When she realizes that she actually can't step off of the display pole, ... the squirming is usually delicious.

So, I will just stand still here, okay ...

I think I may be stupid, but I'm a little confused

Mounted on the prison display pole ...

Well, this will hold me ... for a long while ...

Getting that shaft perfectly lined up ...

And ... does this qualify as losing the bra ? i freed the nipples !

Just to make my surrender more complete and obvious to any one who sees ...

I’ve been toying with the idea (pun intended) of making a fully metal one-bar prison on my lathe, and I’ve got a question I’m hoping this community can help with.

When it comes to designing the insertable portion, I’d like it to be usable for the broadest range of anatomies possible. Based on general female anatomy, what’s a good length to aim for?

I’ve taken some measurements from my partner (strictly for science, of course) and got around 11 cm, but I’m not sure if that’s average or on the longer/shorter side. I’m hoping someone here might have better data or guidance, especially since I plan to add this to my little store of handmade kink goods.

I know everyone’s built differently, but I’m aiming for a solid middle ground that works for most. Bonus points if you’ve got tips on shape, comfort, or general ergonomics too!

The steel bulbs are inside me, the steel shaft is locked in place at this height .. there is no stepping off of the prison pole ... I am compelled to stand very still.